Safety Shoe Markings Explained: SB, S1, S3 and the Codes on the Label
Share
Safety shoes are among the most widely issued items of PPE on Singapore worksites, factories and warehouses. Most buyers know they need a toecap. Fewer know what the rest of the codes on the label mean, which is how teams end up with shoes that let water in on a wet site, or with no puncture protection where nails and metal offcuts are everywhere.
This guide explains the markings so you can specify footwear by the hazard, not just the price or style.
The standards behind the markings
- EN ISO 20345 – safety footwear with a toecap tested to 200 J impact. This is the standard most site and industrial safety shoes are made to. Marked with an S category.
- EN ISO 20346 – protective footwear with a lower-rated toecap. Marked with a P category.
- EN ISO 20347 – occupational footwear without a toecap, for example for some kitchen or healthcare roles. Marked with an O category.
For construction, manufacturing, logistics and M&E work, you will normally be specifying EN ISO 20345 footwear.
The basic categories
| Marking | What it adds | Typical use |
|---|---|---|
| SB | Basic requirements including the 200 J toecap | Rarely the right choice on its own |
| S1 | SB plus closed heel, antistatic and energy absorption at the heel | Dry indoor areas: warehouses, workshops, stores |
| S2 | S1 plus resistance to water penetration and absorption of the upper | Indoor areas with some water or cleaning |
| S3 | S2 plus perforation (puncture) resistance and a cleated outsole | Construction sites, outdoor work, demolition |
| S4 / S5 | Moulded rubber or polymer boots; S5 adds perforation resistance | Wet sites, wash-down areas, drains, marine work |
A common specification for Singapore construction sites is S3, because of rain, mud and the risk of stepping on nails or rebar offcuts. For a dry warehouse floor, S1 or an S1 with puncture protection is usually enough.
Additional codes
Extra letters on the label show protection beyond the basic category:
- P – perforation resistance. Recent editions of the standard split this into P (metal midsole) and PL or PS (non-metallic midsoles tested with different nail sizes).
- A – antistatic.
- C – conductive. Used only for specific applications.
- E – energy absorption at the heel.
- WR – water resistance of the whole shoe.
- HRO – heat-resistant outsole, for hot surfaces such as asphalt and some metalworking areas.
- HI / CI – heat or cold insulation of the sole.
- M – metatarsal protection over the top of the foot.
- AN – ankle protection.
- SR – additional slip resistance tested on a ceramic tile with glycerine.
Electrostatic dissipative (ESD) footwear for electronics work is tested to a separate standard and is marked separately; antistatic (A) is not the same thing.
A note on editions
EN ISO 20345 was revised in 2022, and the way some properties are marked changed, particularly slip resistance and perforation resistance. Older stock and certificates may still show the previous codes, such as SRA, SRB and SRC for slip. Both may be on the market at the same time. When comparing quotes, check which edition each product's certificate refers to so you are comparing like with like.
Matching footwear to the job
- Construction and civil sites – S3 with SR; consider ankle-height boots for uneven ground.
- Warehouses and logistics – S1 or S1 with P; lightweight designs reduce fatigue on long shifts.
- Commercial kitchens and food plants – slip resistance is the priority; choose water-resistant uppers that are easy to clean.
- Welding and hot work – HRO outsoles and designs without exposed laces where sparks may land.
- Marine, drains and wash-down – S5 rubber or polymer boots.
- Electrical work – ordinary safety shoes do not provide electrical insulation. Electrical hazard footwear is a separate product type; specify it deliberately if your risk assessment calls for it.
Fit, care and replacement
A shoe that does not fit will not be worn properly. Offer a range of sizes, and consider wide-fit options. Replace footwear when the toecap is exposed or dented after an impact, the sole is worn smooth or separating, or the upper is split. Under the WSH Act, employers have a duty to provide suitable PPE where risks cannot be eliminated, so keep a record of issue and replacement.
Documents to ask for
- The EN ISO standard and edition, and the full marking string.
- The certificate or declaration of conformity if your client requires it.
- Size range and availability for repeat orders.
Browse safety footwear, gloves and other protection in our PPE and safety gear range, and site first aid supplies in fire safety and first aid.
Get a quote
Need a bulk order across several sizes, or a match for footwear you already issue? Send us the part number, a photo or the old label and a real person will quote within 24 hours. For technical questions about markings or certificates, email cs@delight.com.sg.