Epoxy, PU, Contact or Instant Glue? Choosing Adhesives for Maintenance and Fit-Out

Adhesives are now used for jobs that once needed screws, rivets or brackets: fixing skirting and panels, bonding metal trims, repairing furniture, securing signage and patching equipment. The right glue gives a clean, lasting bond. The wrong one fails within weeks, often in Singapore's heat and humidity.

This guide compares the main adhesive families and the questions to ask before choosing one.

Start with three questions

  1. What are you bonding? Both surfaces matter: metal to metal, wood to concrete, plastic to glass. Some plastics, such as polyethylene and polypropylene, are hard to bond with most adhesives.
  2. How big is the gap? Some adhesives need close-fitting surfaces; others fill gaps and uneven substrates.
  3. Where will it live? Indoors, outdoors, in wet areas, near heat, or under vibration and load.

The main adhesive families

Type Strengths Watch out for
Two-part epoxy Very strong, gap filling, bonds metal, stone, ceramics and many plastics Must be mixed in the right ratio; limited pot life; slower cure
Polyurethane (PU) adhesive Strong, slightly flexible, good for wood and construction materials, tolerates moisture Some types foam as they cure; needs clamping
MS polymer / hybrid Bonds and seals, flexible, works on many building materials, often usable on damp surfaces Lower ultimate strength than epoxy; slower full cure
Contact adhesive Instant grab for laminates, rubber, leather, large flat sheets Solvent-based types need good ventilation; no repositioning once surfaces touch
Cyanoacrylate (instant glue) Very fast for small parts, rubber and many plastics Brittle; poor gap filling; weak on large or flexing joints
PVA / wood glue Easy to use for wood and carpentry Standard types are not water resistant; check the grade for wet areas
Construction / panel adhesive Fixing boards, skirting, panels and trims to walls Needs support while curing; check suitability for the substrate

Terms on the datasheet

Open time

How long the adhesive stays workable after it is applied, before the parts must be joined. Short open times are a problem for large panels in hot conditions.

Pot life

For two-part adhesives, how long the mixed batch stays usable. Heat shortens it, so mix small amounts on hot sites.

Handling strength and full cure

Handling strength is when the joint can be moved without falling apart. Full cure is when it reaches its stated strength. Do not load a joint until it has cured to the level the datasheet specifies.

Service temperature

The temperature range the cured bond is designed for. Important for bonds near hot water pipes, machinery, kitchens or metal roofs.

Surface preparation makes the biggest difference

Most adhesive failures are surface failures, not glue failures. Follow the manufacturer's instructions, and as a general rule:

  • Remove dust, oil, old sealant and loose paint.
  • Lightly abrade smooth metals and plastics to give a key.
  • Degrease with a suitable cleaner and let it dry fully.
  • Use a primer where the datasheet recommends one, particularly on porous or difficult substrates.
  • Clamp, tape or support the parts until handling strength is reached.

Test on a small area first when bonding unfamiliar materials or painted surfaces.

Adhesive or sealant?

An adhesive is chosen for strength. A sealant is chosen to keep water and air out while allowing movement. Hybrid products do some of both, but if a joint mainly needs to stay watertight and flexible, a sealant is usually the better choice. Our earlier guide on choosing between silicone, acrylic and PU sealants covers that side.

Documents to ask your supplier for

  • Technical data sheet (TDS) – suitable substrates, open time, cure time, strength and temperature range.
  • Safety data sheet (SDS) – hazards, ventilation, PPE, storage and first aid. Keep it on site for your risk assessment.
  • Shelf life and batch or expiry date – adhesives past their date may not cure properly.
  • Storage conditions – many products should be kept away from direct sun and high heat.

For solvent-based contact adhesives and some epoxies, plan for ventilation and suitable gloves and eye protection, particularly in enclosed spaces such as toilets, store rooms and ceiling voids.

Browse the range

See our adhesives and glues for epoxies, contact adhesives and instant glues, our sealants and protective coatings for joints that must stay watertight, and paint and painting supplies for finishing after repair.

Get a quote

Looking for a specific brand or grade, or a replacement for a product that is no longer available? Send us the part number, a photo or the old label and a real person will quote within 24 hours. For technical questions about substrates or cure times, email cs@delight.com.sg.

Back to blog