Drill Bits, Saw Blades and Cutting Discs: Choosing by Material
Share
A good drill or grinder is only as useful as the accessory fitted to it. The wrong bit burns out in stainless steel, the wrong blade tears laminate, and the wrong disc can be a safety hazard. This guide is for M&E contractors, maintenance teams and workshop buyers who need to order bits, blades and discs that match the material and the machine.
Start with three questions
- What material are you cutting or drilling? Mild steel, stainless steel, concrete, tile, timber and plasterboard each need a different accessory.
- What machine will it go on? Shank type, arbor size, disc diameter and rated speed must match the tool.
- How many holes or cuts? For a one-off job a standard grade is fine. For production or repeated site work, a premium grade usually costs less per hole.
Drill bits by material
| Material | Bit type | Notes |
|---|---|---|
| Mild steel, aluminium | HSS (high-speed steel) | Use cutting fluid on steel. Titanium-coated HSS lasts longer in general maintenance work. |
| Stainless steel, hard alloys | HSS-Co (cobalt, often marked HSS-E or M35/M42) | Run at lower speed with steady pressure. Stainless work-hardens if the bit rubs instead of cuts. |
| Concrete, brick, block | Carbide-tipped masonry or SDS bits | Use with hammer action. SDS-plus for light and medium rotary hammers, SDS-max for heavy ones. |
| Ceramic and porcelain tile, glass | Diamond or tile bits | No hammer action. Keep the bit cool with water where the bit allows wet use. |
| Timber, plywood | Brad-point, spade or auger bits | Brad-point for clean holes; spade bits for quick, rough holes. |
| Large holes in concrete | Diamond core bits | Used with a coring machine; check thread type and wet or dry rating. |
Shank types to check
Round and hex shanks fit standard chucks and impact drivers. SDS-plus and SDS-max only fit their matching rotary hammers and are not interchangeable. Core bits use threaded connections, so confirm the thread on your coring machine before ordering. If in doubt, send a photo of the tool's chuck or the old bit.
Saw blades: tooth count and material
For circular saws and mitre saws, check the blade diameter, bore size and maximum RPM printed on the blade, and match them to the saw. Then pick the tooth count by finish:
- Fewer teeth (around 24T): fast rip cuts in timber, rougher finish.
- More teeth (40T–80T): cleaner cross-cuts in timber, plywood and laminate.
- Non-ferrous or aluminium blades: a different tooth geometry for aluminium profiles and trunking.
- Metal-cutting dry blades: for steel on saws designed for them only.
For jigsaws and reciprocating saws, check the shank type (T-shank is the most common for jigsaws) and the TPI (teeth per inch). Low TPI cuts fast in timber; high TPI is for metal and thin sheet.
Cutting and grinding discs
Discs for angle grinders deserve the most care, because a disc that fails at speed can cause serious injury.
- Size and bore: match the disc diameter (such as 100 mm, 125 mm or 180 mm) and bore to the grinder and guard.
- Maximum speed: the RPM or m/s rating printed on the disc must be equal to or higher than the grinder's no-load speed. Never fit a disc rated below the tool's speed.
- Type: thin cutting discs (around 1 mm) for cutting steel and stainless; thicker grinding discs for weld removal and shaping; flap discs for blending and finishing; diamond discs for tile, stone and concrete.
- Material marking: discs marked "INOX" or for stainless are formulated to avoid contaminating stainless steel.
- Expiry date: resin-bonded discs usually carry a use-by date stamped on the centre ring. Rotate stock and do not use expired discs.
Always use the grinder with its guard fitted and wear eye and face protection. Cutting discs are for cutting only; do not side-grind with them.
Storage and stock tips
- Keep discs flat and dry. Moisture can weaken resin-bonded discs.
- Label bins by material, not just by size, so site teams grab the right type.
- Keep a small stock of the two or three sizes your team uses most, and order specialist items per job.
Where to start
Browse bits, blades and discs for accessories, power tools for drills, grinders and saws, and drills and coring machines for heavier concrete work.
Request a quotation
Need a mixed order of accessories or a match for an old part? Request a quotation. Send us the part number, a photo or the old label and a real person will quote within 24 hours. For technical questions about shank types, speeds or disc grades, email cs@delight.com.sg.